点击图片查看原图
BDJC-30KV塑料薄膜击穿电压试验机
塑料薄膜击穿电压试验机满足标准：
塑料薄膜击穿电压试验机满足标准：
1、GB1408.1-2006《绝缘材料电气强度试验方法》
2、GB1408.2-2006《绝缘材料电气强度试验方法
第2部分：对应用直流电压试验的附加要求》
3、GB/T1695-2005《硫化橡胶工频击穿电压强度和耐电压的测定方法》
4、GB/T3333 电缆纸工频电压击穿试验方法
5、HG/T 3330绝缘漆漆膜击穿强度测定法
6、GB12656 电容器纸工频电压击穿试验方法
7、ASTM D149《固体电绝缘材料工业电源频率下的介介电强度的试验方法》
塑料薄膜击穿电压试验机试验方式：
1、绝缘试样空气中击穿或耐压试验
2、绝缘试样浸油中击穿或耐压试验
3、绝缘试样空气中阶梯击穿或耐压试验
4、绝缘试样浸油中阶梯击穿或耐压试验
注：根据用户要求，可定制其他试验方式
塑料薄膜击穿电压试验机试验软件：
1、本仪器在试验过程中可对升压击穿过程绘制实时曲线，每次试验的升压曲线都由不同颜色构成，试验结束后可叠加对比材料的试验数据重复性。
2、可以随时调取当前及历史试验数据进行查看，编辑及修改参数。
3、试验过程中可以随时修改试验条件及存储路径及自动存储试验结果。
4、试验过程中，可随时通过软件决定本次试验是否有效，方便筛选试验结果。
5、可设置操作口令，做到专机专人操作，避免无关人员误操作。
塑料薄膜击穿电压试验机技术指标：
1、输入电压AC220V50Hz
2、输出电压AC：0～20kV；DC：0～20kV
3、输出功率2kVA
4、测量范围AC～20kV；DC～20kV
5、测量误差≤2％
6、升压速率1kV/s～5kV/s
7、耐压时间0～6H
8、漏电流1～30mA可由计算机软件自由进行设定
9、电源交流220V±10%的单相交流电压和50Hz±1%的频率
10、试验环境温度：15～30℃，相对湿度：0～85%能够稳定运行。
11、外形尺寸长×宽×高：800mm×800mm×1450mm
12、设备自重100Kg
13、仪器需要单独接地，接地附合国家标准要求，金属棒深埋地下至少要1.5米以下
塑料薄膜击穿电压试验机试验软件简介：
此设备软件外观由专业的美工设计：
人员管理：可添加多人同时使用此软件 不同人员设定不同密码 交叉使用互不干扰 （如一人使用可删除设定密码 直接进入软件）
参数管理：高压保护可选、 耐压时间可选、 梯度步进可选 、漏电流和过压可选、灵敏的漏电压可选、漏电流可选 、升压速度可自由设定（0-10kv 无极自由）试验结果可选 异地操作选定 、人机分离选定等等
结果调取：试验结果保存调取 、人员选定调去 、试验结果可根据客户要求操作整理 、支持5次以上彩线对比、自动整取添加试验数据。
交直流实验的切换
1）本仪器高压输出为交流电压。直流的获得方式为在原回路中串入高压硅堆，使测试回路为脉动的直流电压。实现的过程为：硅堆已经在高压变压器的高压绝缘塔中，平时用一个短路杆把高压硅堆短接。需要直流试验时，取出短路杆，使高压硅堆接入测试电路中，这时回路的电压为脉动的直流电压。
2）前面板直流交流选择按钮。该按钮的状态不能改变设备输出的电压性质。按下该按钮，设备仅仅是把直流报警电路接入。指示用户，当打开箱门时，您需要对高压均压球放电。转动放电杆，使放电杆的端部铜球接触高压均压球。建议用户每次放电铜球接触高压均压球时间大于五秒。
3）试验的交直流电压切换，主要取决于高压绝缘塔中的短路杆是否取出。当取出短路杆时，高压均压球上的电压为直流电压，插入短路杆时，高压均压球上的电压为交流电压。短路杆的取出、插入参看左侧的示意图。
北广精仪公司其它绝缘材料检测仪器:
BDJC-10-100KV 介电击穿试验仪
BDJC系列绝缘材料工频率介电击穿试验仪
BDJC系列电压介电强度试验仪器
BDJC系列 电压击穿试验仪
BDJC系列绝缘漆漆膜击穿强度试验仪
BDJC电容器纸工频电压击穿试验仪
EST-121 体积表面电阻率测定仪
GDAT-A介质损耗测试仪/介电常数测试仪
GDAT-C新型介电常数介质损耗测试仪
BDH 耐漏电起痕试验仪
BDH-B耐电弧试验仪
Meet the standard:
1, GB1408.1-2006 "electrical strength of insulating materials test method"
2, GB1408.2-2006 "test method of electrical strength of insulating materials
The second part: the application of DC voltage test to the additional requirements
3, GB/T1695-2005 "vulcanized rubber power frequency breakdown voltage strength and resistance to voltage measurement method"
4, GB/T3333 cable paper power frequency voltage breakdown test method
5, HG/T 3330 insulation paint film breakdown strength test method
6, GB12656 capacitor paper power frequency voltage breakdown test method
7. D149 ASTM test method for dielectric strength of solid electrical insulating materials at industrial power frequency
Test methods:
1, insulation test specimens in the air breakdown or pressure test
2, insulation breakdown or compressive specimen immersed in test
3, insulation test specimens in the air breakdown or pressure test
The 4 step, the insulation breakdown or compressive specimen immersed in test
Note: according to user requirements, other test methods can be customized
Test software:
1, the instrument in the test process can be used to draw real-time curve of the breakdown process, each test of the boost curve by different color composition, after the end of the test can be superimposed on the test data repeatability of the data.
2, can obtain the current and historical test data to view, edit and modify the parameters.
3, the test process can be modified at any time test conditions and storage path and automatic storage test results.
4, the test process, may at any time through the software to determine whether the test is effective, convenient screening test results.
5, can be set to operate the password, so that the special plane operation, to avoid irrelevant personnel misuse.
Technical index
1, input voltage AC220V50Hz
2, output voltage AC:0 ~ 20kV; DC:0 ~ 20kV
3, output power 2kVA
4, measuring range AC ~ 20kV; DC ~ 20kV
5, the measurement error is less than 2%
6, the boost rate 1kV/s ~ 5kV/s
7, pressure time 0 ~ 6H
8, leakage flow 1 ~ 30mA can be set by the computer software free
9, power AC 220V + 10% of the single-phase AC voltage and 50Hz + 1% of the frequency
10, the test environment temperature: 15 ~ 30 degrees, relative humidity: 0 ~ 85% can be stable operation.
11, appearance size length * width * height: 800mm * 800mm * 1450mm
12, equipment weight 100Kg
13, the instrument needs to be a separate grounding, grounding with the national standard requirements, the metal rod buried at least 1.5 meters below the depth
Brief introduction of test software:
The appearance of this device software is designed by a professional art designer:
Personnel management: can be added to many people at the same time using this software to set different passwords cross use of different passwords do not interfere with each other (such as the use of a person can be removed to set the password directly into the software)
Parameter management: high voltage protection optional, pressure time optional, gradient step into the optional, leakage current and overvoltage optional, sensitive drain voltage is optional, leakage current optional, boost the speed can be set free (0-10kv without liberty) test results optional remote operation is selected, the selected human separation, etc.
The results retrieved: test results are retained for the transfer of personnel selected transferred to, the test results can be according to the customer request operation arrangement, support more than five times the color line contrast, automatically adjust to take to add test data.
Switching of AC and DC experiments
1) the high voltage output of the instrument for AC voltage. The method of obtaining direct current is in series with a high voltage silicon stack in the original circuit, which causes the test loop to have a pulsating DC voltage. Process for silicon stack has been in a high-voltage transformer high-voltage insulating column, usually with a short rod high-voltage silicon stack shorted. When the DC test is needed, the short circuit rod is taken out, and the high-voltage silicon stack is connected with the test circuit.
2) front panel DC AC selection button. The state of the button can not change the nature of the output of the device. Press the button, the device is only the DC alarm circuit access. Indicating the user, when opening the door of the box, you need to discharge the high-pressure. Put the end of the rotation pole, copper ball contact high-pressure discharge pole equalizing ball. Suggest that the user each time the discharge copper ball contact high pressure average pressure ball time is more than five seconds.
3) the test of AC and DC voltage switching, mainly depends on the high voltage insulation tower in the short circuit rod is removed. When the short circuit rod is taken out, the voltage on the high voltage average pressure ball is DC voltage, and the voltage of the high voltage average pressure ball is the voltage of the AC voltage when the short circuit rod is inserted. The drawing of the short circuit rod, and the sketch map of the left.